WOC 2024

Product Search

Search results for 'D6927'

Showing 21 - 41 of 563 Total Results

2” Cube Platen Test Set

(4) options

Location: Test Platens

Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...

Dual Mass DCP, Quick Connect

SA-4010

Location: Dynamic Cone Penetrometer

The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.

Flexural Beam Attachment

(2) options

Location: Test Platens

One fixture tests both 4” and 6” beams. . Used to determine the modulus of rupture for both Center and Third Point beams with depths of either 4” or 6”. The upper heads load bearing blocks are easily changed for center or third point test configuration for either size beam. Bottom support blocks...

Marshall Automatic Double Compactor, 4" Rotating Mold

AA-0022

Location: Marshall Automatic Compactor

Automatically compacts two samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.

Marshall Automatic Single Compactor, 4" Stationary Mold

AA-0020

Location: Marshall Automatic Compactor

The Marshall Automatic Compactor apparatus from Test Mark compacts samples at a preset number of hammer blows and shuts off on completion.

Upper Chamber Body

Upper Chamber Body

CA-0610-08

Location: Parts & Accessories

Upper Chamber Body.

O-Ring Upper Chamber

O-Ring Upper Chamber

CA-0610-09

Location: Parts & Accessories

O-Ring Upper Chamber.

Cutting Edge

SA-2032

Location: CBR Accessories

Machined from seamless tubing with a sharpened edge to enable undisturbed samples to be taken in the field, cutting edge is plated for rust resistance. Recess in upper section allows edge to be mounted at either end of the mold to facilitate sample removal in the field.

Constant Head Permeameter Cell

(5) options

Location: Constant Head Permeameter Cell

The Constant Head Permeameter Cell from Test Mark is used to determine the coefficient of permeability by the constant head method for laminar flow of water through granular soils.

Slump Test Base

CA-0370

Location: Slump Testing

This cast-aluminum base provides a sturdy, level surface on which to perform slump tests. Cleats dig into the ground for firm, level support.

Capping Compound *TEMPORARILY OUT OF STOCK*

CA-0100

Location: Capping Compound

Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.

Chapman Flask

CA-2700

Location: Specific Gravity Flasks

The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.

Marshall Hand Compaction Set

AA-0040-A

Location: Marshall Hand Compaction Set

Set includes Hand Compaction Hammer, 4" Compaction Mold, Compaction Pedestal with Top Plate, Hammer Support Rod with Adjustable Guide and Compaction Mold Holder.

Mortar, 320 ml

SA-0650

Location: Mortar & Pestle

Soil mortar, when used with the pestle, is for pulverizing dry samples of soil and other materials. Mortar is made from heavy porcelain with glazed exterior. Rubber-tipped pestle is 8" long and is for grinding soils without breaking individual particles.

Calibration & Service

Test Mark Industries supplies calibration and service locations for its construction testing equipment.

Marshall Automatic Triple Compactor, 4" Rotating Mold

AA-0024

Location: Marshall Automatic Compactor

Automatically compacts three samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.

Circulating Water Bath, Digital

AA-0065

Location: Circulating Water Bath

The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.

Pestle, Rubber Tipped

SA-0652

Location: Mortar & Pestle

Rubber-tipped pestle is 8" long and is for grinding soils without breaking individual particles.

Magnet Holder with Swivel Adapter Yoke

SA-2021

Location: CBR Accessories

Convenient, portable method of mounting dial indicators. Holder's Alnico magnetic base mounts on flat or curved metallic surfaces. Indicator can me mounted in almost any position.

Vebe Consistometer

(2) options

Location: Vebe Consistometer

The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.